![39604 - Contacta Professional - [Revell]](https://www.robimodelbouw.nl/Files/2/42000/42773/ProductPhotos/Thumbnail/1172920562.jpg)
![39608 - Contacta Professional Mini - [Revell]](https://www.robimodelbouw.nl/Files/2/42000/42773/ProductPhotos/Thumbnail/1172920507.jpg)
![AK12015 - Magnet Ultra Resistant Cyanocrylate Glue - [AK Interactive]](https://www.robimodelbouw.nl/Files/2/42000/42773/ProductPhotos/Thumbnail/1255677531.jpg)
- Home -
- SCENERY & DIORAMA -
- per merk -
- Matho Models -
-
Matho Models 35032 - Wagon Wheels - 1:35
Wagon Wheels
Product Details
Schaal: 1:35
Artikelcode: 35032
Fabrikant: Matho Models
Contains 2 unpainted Wagon Wheels, printed in very high detail UV cured acrylic plastic.
Each wheel has a diameter of 1,85 cm (0,73")
How to work with 3D printed parts?
Be carefull when manipulating 3D printed parts, they can be brittle!
Firstly rinse in Acetone to wash off any excess waxy material. The waxy material is a support material used during 3D printing process. It is very liquid, oil-like and washes off very easily.
After that you can start sanding where needed. The 3D printing process builds up a product in micro-layers. Those layers sometimes remain slightly visible in some areas (especially under magnification), they can be sanded out with a medium sandpaper (like 600 grit), followed by a fine sandpaper (like 1000 grit). Again, the material is not that hard, so it sands very easy. Rinse in Acetone again to wash of any dust.
Some 3D printed models are hollow and open at the bottom that is normally not displayed. Should you do want to display the bottom, simply fill the part with putty and sand.
Now it is ready to prime and paint.
Tip for sanding very small and difficult areas
Cut a small strip of sandpaper 1 - 2 mm wide, fold it and grab it with a tweezers (not the one with a pointy tip, but the one with a flat 1 - 2mm broad tip). Hold it in such a way that the fold is sticking out for only a tiny fraction (make sure it is the fold that is sticking out, and not the loose ends of the strip). Keep holding the tweezers like that and move over the surface you want to sand. When the sandpaper is clogged, make a new fold in an area of the strip that has not been used before, and continue like before.
Product Details
Schaal: 1:35
Artikelcode: 35032
Fabrikant: Matho Models
Contains 2 unpainted Wagon Wheels, printed in very high detail UV cured acrylic plastic.
Each wheel has a diameter of 1,85 cm (0,73")
How to work with 3D printed parts?
Be carefull when manipulating 3D printed parts, they can be brittle!
Firstly rinse in Acetone to wash off any excess waxy material. The waxy material is a support material used during 3D printing process. It is very liquid, oil-like and washes off very easily.
After that you can start sanding where needed. The 3D printing process builds up a product in micro-layers. Those layers sometimes remain slightly visible in some areas (especially under magnification), they can be sanded out with a medium sandpaper (like 600 grit), followed by a fine sandpaper (like 1000 grit). Again, the material is not that hard, so it sands very easy. Rinse in Acetone again to wash of any dust.
Some 3D printed models are hollow and open at the bottom that is normally not displayed. Should you do want to display the bottom, simply fill the part with putty and sand.
Now it is ready to prime and paint.
Tip for sanding very small and difficult areas
Cut a small strip of sandpaper 1 - 2 mm wide, fold it and grab it with a tweezers (not the one with a pointy tip, but the one with a flat 1 - 2mm broad tip). Hold it in such a way that the fold is sticking out for only a tiny fraction (make sure it is the fold that is sticking out, and not the loose ends of the strip). Keep holding the tweezers like that and move over the surface you want to sand. When the sandpaper is clogged, make a new fold in an area of the strip that has not been used before, and continue like before.
Aanmelden nieuwsbrief
Meld u hier aan voor de nieuwsbrief
Aanmelden
ROBI Modelbouw
| Adres: | Schoolstraat 15A | Openingstijden winkel | ||
| 4841 XC PRINSENBEEK | Maandag | gesloten | ||
| Nederland | Dinsdag | gesloten | ||
| Woensdag | 10:00u - 17:30u | |||
| Telefoon | +31 (0)6 123 998 44 | Donderdag | 10:00u - 17:30u | |
| info@robimodelbouw.nl | Vrijdag | 10:00u - 17:30u | ||
| Zaterdag | 10:00u - 17:00u | |||
| Zondag | gesloten | |||
Deze website gebruikt cookies om het bezoek te meten, we slaan geen persoonlijke gegevens op.